HOW TO INSTALL A BATH TUB

How to Install a Bath Tub

How to Install a Bath Tub

Blog Article

Visit Website

Are you trying to find facts concerning Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Installing a tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old bathtub is readily available, the job can relocate speedily; if you have to open up a wall to eliminate the old tub and also place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub and also do not require to transform the plan of your previous water system pipes.
Your tools and material checklist should comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Planning for the Setup


    First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
    Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final position.

    Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
    Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
    The next objective is to make certain that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
    To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
    Turn on the water system and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
    Ultimately, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly settle it into its final position.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end provides a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Protect the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former type ought to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Tub


    In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to permit the activity experienced when the tub remains in use. The sealant can fracture fairly early if you do not think about this movement prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Hopefully you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking the time to browse our short article. Loved our piece? Please share it. Let other people discover it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.



    Click Here To Read More

    Report this page